If all lengths were cut the same, every other length would not match at the top. "Wallpaper patterns might be divided into two primary classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is needed to cut these documents so that the design matches when hung. For this reason factor to consider of the style is needed prior to cutting such papers. The top of a flower or figure need to not be halved. The paper must be so put that an entire flower or figure need to be left about a 1/2 inch below the photo molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper. They are basic and good for tasks in a child's bathroom, with patterns that match the bathroom components or tub. Before cutting the paper, the needed length is to be determined. When this has been done, the paper is unrolled face up. Let us presume that the wall to be covered is 8' high. Allowance needs to be made for cutting and trimming at the top and bottom. This ought to be at least 6"". It might be required to cut more depending upon the pattern. For example, a paper may have a pattern which is 12"" high. If there is no space at the top for cutting, the entire pattern needs to be cut off because, as has been stated, the top should always have a whole pattern resting about 1/2"" below the photo molding or ceiling line. Permitting 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right hand, pull out 11/2"" from the roll. Let this hang over completion of the table, and then unroll 7', which will cover the length of the table. Analyze the style to determine the very best location to cut, keeping in mind that the top of the pattern will be about 1/2"" below the picture molding. This first piece may be a little bit longer in order to get the leading right. The remainder of the paper is cut into equivalent lengths of 8' 6"". Do not do this in the bathroom. No tub is a great work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the style does not fall directly opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjoining pattern will be 10"" below this. It can be seen, then, that a drop pattern paper can not be cut the exact same as a straight-pattern paper. If all lengths were cut the very same, every other length would not match at the top This is especially obvious in small places like restrooms, where the wallpaper is among the only things to look at while waiting for the sauna or sitting in the tub. The wallpaper is noticeable from the shower also. The simplest method to cut these papers is to take lengths from different rolls. Cut the first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths alternately from one roll and the other, keeping the 2 separated. The very first, 3rd, 5th, etc., lengths will have one leading, while the 2nd, 4th, 6th, and so on, will be various. Before hanging the very first width, the location at which to begin must be figured out. This is found by deciding which the most popular walls are. They are normally those between windows and over the mantel. Then determine the least conspicuous place in the room and prepare the work to finish there, so if an inequality happens, it will be least visible. If there is no mantel in the room, the very first width needs to be hung in between the windows. Then follow around to the right, covering one side of the space. Return to the window end and paper the other side. By this plan of procedure, you will always have good light. If you are working in a bathroom with no windows, attempt affixing an intense lamp onto the shower tray or the shower doors (this might be challenging with frameless shower doors) to get rid of most shady corners. If there is a mantel in the room, the very first pieces are put there, because it is the most obvious point. The wall over the mantel is marked so that the paper will be focused. This procedure is as follows: Measure the width of wall over the mantel to discover the center. Draw the line through this center. If the space requires 4 widths, put the first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These 3 widths are brief lengths. The staying part will be covered with 2 partial widths of complete length. Cut these 1/2"" larger than needed, so regarding have the edges turn the corner."