Continue to cut lengths at the same time from one roll and the other, keeping the two separated. The first, third, fifth, etc., lengths will "Wallpaper patterns might be divided into two primary classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is required to cut these papers so that the style matches when hung. For this reason factor to consider of the design is essential before cutting such papers. The top of a flower or figure need to not be cut in half. The paper should be so placed that an entire flower or figure need to be left about a 1/2 inch below the photo molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper. They are easy and good for jobs in a child's bathroom, with patterns that match the restroom components or bath tub. Prior to cutting the paper, the needed length is to be figured out. When this has actually been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance should be produced cutting and trimming at the top and bottom. This need to be at least 6"". It may be needed to cut more depending upon the pattern. For example, a paper might have a pattern which is 12"" high. If there is no space at the top for cutting, the entire pattern must be cut off because, as has actually been said, the top needs to constantly have an entire pattern resting about 1/2"" listed below the image molding or ceiling line. Allowing 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right hand, take out 11/2"" from the roll. Let this hang over completion of the table, and after that unroll 7', which will cover the length of the table. Take a look at the style to identify the very best location to cut, remembering that the top of the pattern will be about 1/2"" listed below the image molding. This very first piece may be a little longer in order to get the top right. The remainder of the paper is cut into equal lengths of 8' 6"". Do refrain from doing this in the bathroom. No bathtub is a great table, even if it is a walk-in bath tub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjacent pattern will be 10"" below this. It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the very same, every other length would not match at the top This is specifically obvious in little locations like bathrooms, where the wallpaper is one of the only things to look at while awaiting the sauna or being in the tub. The wallpaper is noticeable from the shower also. The simplest way to cut these documents is to take lengths from different rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths alternately from one roll and the other, keeping the 2 separated. The very first, 3rd, fifth, and so on, lengths will have one leading, while the second, 4th, sixth, etc., will be different. Before hanging the very first width, the place at which to begin need to be figured out. This is discovered by deciding which the most prominent walls are. They are generally those in between windows and over the mantel. Then figure out the least obvious location in the space and plan the work to finish there, so if an inequality happens, it will be least noticeable. If there is no mantel in the room, the very first width ought to be hung in between the windows. Then follow around to the right, covering one side of the space. Return to the window end and paper the opposite. By this plan of procedure, you will constantly have excellent light. If you are operating in a bathroom with no windows, try affixing a bright light onto the shower tray or the shower doors (this might be hard with frameless shower doors) to eliminate most dubious corners. If there is a mantel in the space, the first pieces are placed there, given that it is the most conspicuous point. The wall over the mantel is marked so that the paper will be focused. This treatment is as follows: Measure the width of wall over the mantel to find the center. Draw a line through this center. If the area requires four widths, put the first width of paper with its center on the center line of the mantel. A full width is put to the left and right of the center piece. These 3 widths are brief lengths. The remaining part will be covered with two partial widths of complete length. Cut these 1/2"" larger than needed, so regarding have the edges turn the corner."