This is especially noticeable in little places like restrooms, where the wallpaper is one of the only things to look at while waiting on the "Wallpaper patterns might be divided into 2 principal classes, the ""one-top"" or straight pattern documents, and the ""two-top"" or drop patterns. It is required to cut these documents so that the design matches when hung. For this reason consideration of the style is needed before cutting such documents. The top of a flower or figure must not be cut in half. The paper must be so placed that an entire flower or figure should be left about a 1/2 inch below the picture molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper. They are basic and great for jobs in a kid's bathroom, with patterns that match the bathroom fixtures or bathtub. Before cutting the paper, the needed length is to be determined. When this has been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance must be produced cutting and cutting at the top and bottom. This must be at least 6"". It may be necessary to cut more depending on the pattern. For instance, a paper may have a pattern which is 12"" high. If there is no room at the top for trimming, the entire pattern must be cut off since, as has actually been said, the top needs to always have a whole pattern resting about 1/2"" listed below the picture molding or ceiling line. Enabling 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the ideal hand, take out 11/2"" from the roll. Let this hang over the end of the table, and after that unroll 7', which will cover the length of the table. Examine the design to figure out the very best place to cut, bearing in mind that the top of the pattern will be about 1/2"" listed below the image molding. This first piece might be a little bit longer in order to get the leading right. The rest of the paper is cut into equivalent lengths of 8' 6"". Do not do this in the bathroom. No bath tub is a great work table, even if it is a walk-in bathtub. A ""two-top"" or drop pattern is one in which the style does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for instance, the adjoining pattern will be 10"" below this. It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the same, every other length would not match at the top This is especially obvious in small places like restrooms, where the wallpaper is among the only things to look at while waiting for the sauna or being in the tub. The wallpaper is visible from the shower too. The most convenient method to cut these papers is to take lengths from separate rolls. Cut the very first length as described for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths at the same time from one roll and the other, keeping the 2 separated. The very first, third, 5th, etc., lengths will have one top, while the second, fourth, 6th, etc., will be different. Before hanging the first width, the location at which to start need to be identified. This is found by choosing which the most popular walls are. They are generally those in between windows and over the mantel. Then figure out the least obvious place in the room and prepare the work to finish there, so if a mismatch happens, it will be least visible. If there is no mantel in the space, the very first width ought to be hung between the windows. Then follow around to the right, covering one side of the room. Go back to the window end and paper the opposite. By this plan of procedure, you will constantly have good light. If you are operating in a bathroom with no windows, try affixing a bright lamp onto the shower tray or the shower doors (this might be hard with frameless shower doors) to eliminate most shady corners. If there is a mantel in the space, the very first pieces are placed there, given that it is the most noticeable point. The wall over the mantel is marked so that the paper will be centered. This procedure is as follows: Measure the width of wall over the mantel to discover the center. Draw a line through this center. If the space needs four widths, position the very first width of paper with its center on the center line of the mantel. A full width is put to the left and right of the center piece. These three widths are short lengths. The staying part will be covered with 2 partial widths of full length. Cut these 1/2"" broader than required, so as to have the edges turn the corner."