The easiest method to cut these documents is to take lengths from different rolls. Cut the first length as explained for a "one-top" pattern. "Wallpaper patterns may be divided into 2 principal classes, the ""one-top"" or straight pattern documents, and the ""two-top"" or drop patterns. It is needed to cut these papers so that the design matches when hung. For this reason factor to consider of the design is needed prior to cutting such documents. The top of a flower or figure must not be halved. The paper needs to be so put that a whole flower or figure ought to be left about a 1/2 inch below the image molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper. They are basic and helpful for tasks in a kid's bathroom, with patterns that match the bathroom components or bath tub. Prior to cutting the paper, the needed length is to be figured out. When this has actually been done, the paper is unrolled face up. Let us presume that the wall to be covered is 8' high. Allowance needs to be made for cutting and cutting at the top and bottom. This must be at least 6"". It might be required to cut more depending on the pattern. For instance, a paper might have a pattern which is 12"" high. If there is no space at the top for cutting, the entire pattern must be cut off given that, as has been said, the top needs to always have a whole pattern resting about 1/2"" below the image molding or ceiling line. Permitting 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the best hand, pull out 11/2"" from the roll. Let this hang over the end of the table, and after that unroll 7', which will cover the length of the table. Examine the style to determine the very best place to cut, keeping in mind that the top of the pattern will have to do with 1/2"" below the photo molding. This very first piece may be a little longer in order to get the top right. The rest of the paper is cut into equivalent lengths of 8' 6"". Do not do this in the restroom. No bath tub is a great work table, even if it is a walk-in bath tub. A ""two-top"" or drop pattern is one in which the style does not fall directly opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for instance, the adjacent pattern will be 10"" below this. It can be seen, then, that a drop pattern paper can not be cut the same as a straight-pattern paper. If all lengths were cut the very same, every other length would not match at the top This is especially obvious in small locations like restrooms, where the wallpaper is among the only things to look at while waiting on the sauna or sitting in the tub. The wallpaper is obvious from the shower too. The simplest method to cut these documents is to take lengths from different rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths at the same time from one roll and the other, keeping the 2 separated. The first, third, fifth, and so on, lengths will have one top, while the 2nd, fourth, sixth, etc., will be different. Before hanging the very first width, the place at which to start should be determined. This is discovered by choosing which the most prominent walls are. They are normally those between windows and over the mantel. Then identify the least noticeable location in the space and prepare the work to end up there, so if a mismatch takes place, it will be least noticeable. If there is no mantel in the space, the first width must be hung in between the windows. Then follow around to the right, covering one side of the space. Go back to the window end and paper the other side. By this plan of procedure, you will constantly have great light. If you are working in a bathroom with no windows, attempt attaching a bright lamp onto the shower tray or the shower doors (this might be hard with frameless shower doors) to eliminate most shady corners. If there is a mantel in the room, the first pieces are placed there, given that it is the most noticeable point. The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Measure the width of wall over the mantel to discover the center. Draw the line through this center. If the area requires four widths, place the first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These 3 widths are brief lengths. The staying part will be covered with 2 partial widths of complete length. Cut these 1/2"" larger than needed, so as to have the edges turn the corner."