This is specifically noticeable in small locations like bathrooms, where the wallpaper is one of the only things to look at while waiting for "Wallpaper patterns might be divided into two principal classes, the ""one-top"" or straight pattern documents, and the ""two-top"" or drop patterns. It is necessary to cut these documents so that the style matches when hung. For this factor consideration of the style is essential before cutting such papers. The top of a flower or figure should not be cut in half. The paper ought to be so placed that an entire flower or figure need to be left about a 1/2 inch below the picture molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper. They are simple and great for tasks in a kid's bathroom, with patterns that match the restroom components or bath tub. Prior to cutting the paper, the required length is to be figured out. When this has been done, the paper is unrolled face up. Let us presume that the wall to be covered is 8' high. Allowance should be produced cutting and cutting at the top and bottom. This ought to be at least 6"". It may be required to cut more depending upon the pattern. For example, a paper may have a pattern which is 12"" high. If there is no room at the top for trimming, the whole pattern must be cut off because, as has actually been said, the top should always have a whole pattern resting about 1/2"" below the photo molding or ceiling line. Permitting 6"" for trimming, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right-hand man, take out 11/2"" from the roll. Let this hang over the end of the table, and after that unroll 7', which will cover the length of the table. Examine the design to identify the very best place to cut, keeping in mind that the top of the pattern will have to do with 1/2"" below the image molding. This very first piece might be a little longer in order to get the leading right. The remainder of the paper is cut into equivalent lengths of 8' 6"". Do not do this in the restroom. No tub is an excellent work table, even if it is a walk-in bath tub. A ""two-top"" or drop pattern is one in which the design does not fall directly opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjacent pattern will be 10"" listed below this. It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the exact same, every other length would not match at the top This is particularly noticeable in little places like bathrooms, where the wallpaper is among the only things to take a look at while waiting on the sauna or sitting in the tub. The wallpaper is obvious from the shower too. The simplest way to cut these documents is to take lengths from separate rolls. Cut the first length as described for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths alternately from one roll and the other, keeping the two separated. The very first, third, fifth, and so on, lengths will have one leading, while the 2nd, fourth, sixth, etc., will be different. Before hanging the very first width, the place at which to start need to be identified. This is discovered by deciding which the most popular walls are. They are normally those in between windows and over the mantel. Then figure out the least obvious location in the space and plan the work to end up there, so if an inequality happens, it will be least obvious. If there is no mantel in the room, the very first width must be hung between the windows. Then follow around to the right, covering one side of the space. Return to the window end and paper the other side. By this plan of treatment, you will always have good light. If you are operating in a restroom with no windows, attempt attaching a brilliant light onto the shower tray or the shower doors (this may be difficult with frameless shower doors) to get rid of most shady corners. If there is a mantel in the space, the first pieces are put there, because it is the most noticeable point. The wall over the mantel is marked so that the paper will be focused. This procedure is as follows: Determine the width of wall over the mantel to find the center. Draw the line through this center. If the area requires four widths, put the first width of paper with its center on the center line of the mantel. A full width is put to the left and right of the center piece. These three widths are brief lengths. The remaining part will be covered with two partial widths of full length. Cut these 1/2"" larger than required, so as to have the edges turn the corner."